{"product_id":"hj-wb-holden-gts-retrotech-dash-kit-saas-series-3","title":"HJ–WB Holden GTS RetroTech Dash Kit · SAAS Series 3","description":"\u003cp\u003eWant the iconic GTS dash in your \u003cstrong\u003eHJ, HX, HZ or WB Holden\u003c\/strong\u003e without hunting down original GTS instruments? The Emdawg \u003cstrong\u003eRetroTech HJWBGTSS3 GTS Dash Kit\u003c\/strong\u003e fills in every missing piece of a non-GTS to GTS dash conversion, and gives you accurate, modern \u003cstrong\u003eSAAS Muscle Series 3\u003c\/strong\u003e electronic gauges with a classic analogue look.\u003c\/p\u003e\n\u003cp\u003eNew reproduction GTS fascias are available from Rare Spares and other suppliers, but they don't come with gauges, indicator lights or warning light globes. This kit supplies them, including our pilot light cluster that brings back the GTS turn signal, high beam and hand brake lights. It screws straight into the clock hole, so there's no cutting of your new fascia.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003e✅ Vehicle Fitment\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHJ, HX, HZ and WB Holden fitted with a GTS dash fascia (original or reproduction)\u003c\/li\u003e\n\u003cli\u003eMade for Kingswood (non-GTS) to GTS dash conversions\u003c\/li\u003e\n\u003cli\u003eGTS dash fascia not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003ch3\u003e✅ What's in the Kit\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e3D-printed GTS gauge pods: left and right main gauge pods plus the 4-gauge auxiliary pod, printed in high-temperature engineering-grade filament\u003c\/li\u003e\n\u003cli\u003eSAAS Muscle Series 3 gauges, pre-installed: 80mm speedo and tacho, 52mm fuel, oil pressure, water temp and volts\u003c\/li\u003e\n\u003cli\u003eLower auxiliary gauge bezels already machined for clearance\u003c\/li\u003e\n\u003cli\u003eSAAS oil pressure and water temp senders\u003c\/li\u003e\n\u003cli\u003eAuxiliary gauge cluster pre-wired to 3 Deutsch DT plugs: power and ground, sensors, and programming buttons\u003c\/li\u003e\n\u003cli\u003ePilot light cluster (clock delete), pre-wired with four 12V 14mm LED pilot lights: left and right indicators, high beam and hand brake\u003c\/li\u003e\n\u003cli\u003eBrake fail and battery charge warning light sockets with T5 LED globes. The battery light has a built-in resistor so the alternator charge circuit works properly\u003c\/li\u003e\n\u003cli\u003eCar-side Deutsch DT connectors for a clean install that's easy to remove and service\u003c\/li\u003e\n\u003cli\u003eAll-new mounting brackets and screws\u003c\/li\u003e\n\u003cli\u003eFull printed installation manual, including Kingswood-to-GTS wiring instructions\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003ch3\u003e✅ GTS Indicator \u0026amp; Warning Lights, No Cutting\u003c\/h3\u003e\n\u003cp\u003eThe original GTS speedo and tacho have the turn signals and high beam built in, but the SAAS gauges don't. Our pilot light cluster puts them back in the original clock position, where they're easy to see even with a sports steering wheel. If your car used a single combined \"brake fail \/ hand brake\" light, the kit lets you split them into separate warning lights.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003e✅ SAAS Muscle Series 3 Gauge Features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eClassic analogue styling with red needles and bright aluminium bezels\u003c\/li\u003e\n\u003cli\u003eAccurate electronic speedo, tacho, oil pressure and water temp, a big step up from tired factory gauges\u003c\/li\u003e\n\u003cli\u003eMultifunction display: odometer, shift light, overspeed alert, low fuel warning and more\u003c\/li\u003e\n\u003cli\u003e10 LED backlight colours: red, green, blue, purple, white, amber, pink, ice blue, orange and aqua\u003c\/li\u003e\n\u003cli\u003eSeparate day and night brightness settings\u003c\/li\u003e\n\u003cli\u003eRemote programming buttons for easy setup and calibration\u003c\/li\u003e\n\u003cli\u003eGreat for stock rebuilds, modified engines and LS or other modern drivetrain swaps\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003ch3\u003e✅ Speedometer: VSS, Converter or GPS\u003c\/h3\u003e\n\u003cp\u003eThe SAAS speedo is electronic. If your transmission has a VSS output, connect it directly. If it still runs a speedo cable, choose a \u003cstrong\u003eSpeedometer input interface\u003c\/strong\u003e above:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSAAS GPS sensor \u0026amp; antenna:\u003c\/strong\u003e works with any transmission, no calibration needed\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eESA-01:\u003c\/strong\u003e cable-to-pulse converter for GM transmissions (Powerglide, TH350, TH400)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eESA-01 + ESA-02:\u003c\/strong\u003e converter plus cable adapter for Holden transmissions (Trimatic, M20, M21)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e⚠️ \u003cem\u003ePlease check your local regulations regarding GPS speed signals.\u003c\/em\u003e\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003e✅ Installation\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eSome clearance work is needed: a few millimetres are trimmed from the two lower mounting posts on the cluster's aluminium mount\u003c\/li\u003e\n\u003cli\u003eWiring required: ignition, constant 12V, ground, instrument lights, fuel, tacho and speedo signals, oil and temp senders, and the pilot lights\u003c\/li\u003e\n\u003cli\u003eTools: basic hand tools, a multimeter, soldering or crimp tools, wire strippers and a Deutsch crimp tool (or choose the pre-crimped Deutsch tails option). A die grinder or Dremel is handy for the clearance work\u003c\/li\u003e\n\u003cli\u003eThe manual covers removing the old cluster, the clearance work, wiring from a Kingswood dash, start-up checks and troubleshooting\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eYou'll need to be confident removing the instrument cluster and doing automotive wiring. If unsure, have an auto electrician fit it.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003e✅ Designed \u0026amp; Made in Australia\u003c\/h3\u003e\n\u003cp\u003eDesigned, assembled and tested in Australia by Emdawg JDM. We want your dash up and running as much as you do. If you have any questions or need support, get in touch at \u003ca href=\"mailto:emdawgdrift@gmail.com\"\u003eemdawgdrift@gmail.com\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003eSupplying your own gauges? See the \u003ca href=\"\/en-jp\/products\/hj-wb-holden-gts-retrotech-bare-dash-kit\"\u003eHJ–WB Holden GTS RetroTech Bare Dash Kit\u003c\/a\u003e. More parts for your car: \u003ca href=\"\/en-jp\/collections\/hj-wb-holden-parts\"\u003eHJ–WB Holden Parts\u003c\/a\u003e.\u003c\/p\u003e\n","brand":"Emdawg","offers":[{"title":"No \/ None – transmission has VSS output","offer_id":67940029530186,"sku":"HJWBGTSS3","price":136200.0,"currency_code":"JPY","in_stock":true},{"title":"No \/ SAAS GPS sensor \u0026 antenna (+$125)","offer_id":67940029562954,"sku":"HJWBGTSS3-GPS","price":150100.0,"currency_code":"JPY","in_stock":true},{"title":"Yes (+$40) \/ None – transmission has VSS output","offer_id":67940029595722,"sku":"HJWBGTSS3-DC","price":140600.0,"currency_code":"JPY","in_stock":true},{"title":"Yes (+$40) \/ SAAS GPS sensor \u0026 antenna (+$125)","offer_id":67940029628490,"sku":"HJWBGTSS3-DC-GPS","price":154600.0,"currency_code":"JPY","in_stock":true},{"title":"No \/ ESA-01 – GM transmissions e.g. Powerglide\/TH350\/TH400 etc. (+$145)","offer_id":67941140136010,"sku":"HJWBGTSS3-ESA1","price":152300.0,"currency_code":"JPY","in_stock":true},{"title":"No \/ ESA-01 + ESA-02 – Trimatic\/M20\/M21 (+$308)","offer_id":67941140168778,"sku":"HJWBGTSS3-ESA12","price":170500.0,"currency_code":"JPY","in_stock":true},{"title":"Yes (+$40) \/ ESA-01 – GM transmissions e.g. Powerglide\/TH350\/TH400 etc. (+$145)","offer_id":67941140201546,"sku":"HJWBGTSS3-DC-ESA1","price":156800.0,"currency_code":"JPY","in_stock":true},{"title":"Yes (+$40) \/ ESA-01 + ESA-02 – Trimatic\/M20\/M21 (+$308)","offer_id":67941140234314,"sku":"HJWBGTSS3-DC-ESA12","price":175000.0,"currency_code":"JPY","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0561\/6232\/0458\/files\/01-hj-wb-gts-dash-kit-saas-series-3-render.jpg?v=1794278458","url":"https:\/\/emdawgjdm.com\/en-jp\/products\/hj-wb-holden-gts-retrotech-dash-kit-saas-series-3","provider":"EMDAWG JDM","version":"1.0","type":"link"}