Fitting an electronic speedo, like the SAAS Muscle Series 3 or Muscle Digital speedos in our RetroTech dash kits, behind a TH350? The gearbox only has a mechanical speedo cable output, and an electronic speedo needs an electrical speed signal. This guide shows how to make that signal straight from the TH350 (and the TH400 and Powerglide), what to check before you buy, and how to wire and calibrate it.
Why a TH350 needs a converter
A TH350 drives the speedo with a gear on the output shaft, which turns a driven gear in the tailshaft housing. The speedo cable screws onto that housing and spins at a speed that matches road speed. An old-style mechanical speedo reads that spinning cable directly.
An electronic speedo has no cable input. It counts electrical pulses instead. So you either:
- convert the cable output into pulses with a sender that screws onto the gearbox, or
- skip the gearbox and use a GPS speed sensor.
This guide covers the first option. For a side-by-side look at both, see GPS speed sensor vs ESA-01.
The ESA-01 converter
The ESA-01 screws onto the TH350's speedo cable output in place of the cable. As the driven gear turns, it sends a 12V square wave signal (16 pulses per revolution) to your speedo.
- No changes to the gearbox: it uses the existing speedo output
- CNC-machined aluminium body
- Waterproof 3-pin locking connector
- 2.7m double-insulated wiring loom included
- Works with SAAS electronic speedos and many other aftermarket speedos that take a 12V square wave input
Which gearboxes it fits
The standard ESA-01 suits GM gearboxes with a 7/8"-18 speedo cable thread and a 0.104" (2.64 mm) square drive, including:
- TH350
- TH400
- Powerglide
Common Holden gearboxes use a different cable connection. For these, add the ESA-02 cable adapter, which fits between the gearbox and the ESA-01:
- Holden Trimatic
- M20 4-speed manual
- M21 4-speed manual
Running a 4L60E or another electronic gearbox? These already have a vehicle speed sensor, so you don't need a converter. Your speedo can usually take its signal from the gearbox or the engine computer.
Check these before you buy
- The thread on the gearbox. Unscrew your speedo cable. A TH350, TH400 or Powerglide should have the 7/8"-18 thread.
- The square drive. Look into the speedo output. The ESA-01 needs a 0.104" (2.64 mm) square drive.
- The driven gear and its housing. Pull the cable and check the driven gear turns freely, isn't chewed and doesn't leak. A worn gear gives a jumpy reading, mechanical or electronic.
- Previous modifications. Gearboxes that have been swapped or rebuilt can have different tailshaft housings. If you're not sure, send us a photo before you order.
Wiring it up
The ESA-01 has three wires:
- 12V ignition supply, fused, so the sender only has power with the key on
- Ground, to a clean chassis or engine earth
- Speed signal, to the speed input on your speedo
Run the loom away from the exhaust, tailshaft and anything that moves, and tie it off every so often. Keep the signal wire away from ignition leads and coil wiring, as electrical noise can make the needle flicker. For general tips on running power, earths and senders, see our aftermarket gauge wiring guide.
Calibrating the speedo
An electronic speedo has to learn how many pulses equal a kilometre. That depends on your diff ratio, the speedo gears in the gearbox and your tyre size. You don't need to change any gears to get it right, because you calibrate the speedo itself.
Follow the calibration steps in your speedo's instructions. With SAAS speedos this is usually done by driving a set distance (often 1 km) during calibration mode, so the speedo counts the pulses itself. Use a measured distance, or a GPS app on a quiet road, to check the reading afterwards. If you later change the diff ratio or tyre size, just calibrate again.
Common questions
Will this work on an LS-swapped Holden with a TH350 or TH400?
Yes. The converter only cares about the gearbox, not the engine. If you're planning an LS swap, our LS swap gauges and senders guide covers the rest of the gauges.
Can I still use my old mechanical speedo?
No. The converter replaces the cable, so the speedo has to be electronic.
Does the speedo gear in the gearbox need to match my diff ratio?
Not for accuracy, because the speedo is calibrated electronically. The gears just need to be in good condition.
Will it pass engineering?
Requirements vary between states. Talk to your engineer about your plans before you buy. Some prefer a gearbox-driven signal over GPS-only for an engineered car.
Parts for the job
- ESA-01 GM transmission to electronic speedo converter
- ESA-02 cable adapter for Trimatic, M20 and M21
- SAAS gauges, including electronic speedos
- Gauge sensors and converters
- RetroTech dash kits for VB–VK Commodores
Not sure what your gearbox has? Get in touch with your car, gearbox and a photo of the speedo output, and we'll confirm what you need.
