The GTS dash is one of the most popular upgrades for an HJ, HX, HZ or WB Holden. Round gauges, a proper tacho and that unmistakable early-'70s muscle look turn a plain Kingswood interior into something special. With reproduction GTS fascias now readily available, a lot of sedans, utes, panel vans and One Tonners are getting the conversion.
The fascia is the easy part. Here's everything else a Kingswood to GTS dash conversion needs, the three ways to do it, and the traps people only find once the fascia is in.
Which cars can have the HJ–WB GTS dash?
The HJ, HX, HZ and WB share the same dash, so a GTS fascia suits all four, including:
- HJ, HX and HZ sedans and wagons
- Utes, panel vans (including Sandmans) and One Tonners
The HQ is different. The HQ uses its own dash design, so HJ–WB GTS dash parts don't fit an HQ. Not sure which series you've got, or whether the front has been swapped? Check our HQ to WB identification guide before you buy anything.
What a Kingswood to GTS dash conversion needs
A reproduction GTS fascia gives you the shape, the gauge holes and the warning-light windows. It doesn't give you anything that makes it work. You'll need to sort out:
- The fascia. Original or reproduction. Reproductions are available from Rare Spares and other suppliers.
- Gauges. A speedo and tacho for the two big holes, plus fuel, oil pressure, water temp and volts.
- Something to mount them. Aftermarket gauges won't bolt into the GTS dash on their own. They need pods or mounts made to fit behind the fascia.
- Indicator and high beam lights. On the factory GTS dash these are built into the speedo and tacho. Fit aftermarket gauges and you lose them, which is a roadworthy problem as well as an annoyance. More on that below.
- Brake fail and battery charge warning lights. Reproduction fascias have the windows and lenses, but no globes, sockets or wiring.
- Wiring. A Kingswood loom isn't laid out for the GTS cluster, so it needs rewiring for the new gauges and lights.
- A speed signal. Most of these cars still run a mechanical speedo cable. Modern electronic speedos need an electrical signal instead.
The indicator light problem (and the clock hole)
This is the one that catches most people out. Original GTS gauges have the left and right indicators and the high beam light built into the speedo and tacho faces. Most aftermarket gauges don't, so once they're in, you've got no blinker or high beam indicators on the dash.
The usual fixes are drilling the fascia for pilot lights (risky on a fascia that's expensive to replace) or limiting yourself to gauges with built-in indicators. The cleanest answer is the clock hole. Plenty of builders don't use the GTS clock, it's in clear view even with a small sports wheel, and using it needs no cutting. We go into this in detail in HJ–WB GTS Dash: Indicator & Warning Lights for Aftermarket Gauges.
Speedo cable? Your options for the speed signal
An electronic speedo counts pulses, so a car still running a speedo cable needs one of these:
- GPS speed sensor: works with any gearbox and needs no speedo calibration. Check your local regulations on GPS speed signals.
- ESA-01 converter: screws onto the gearbox's cable output and turns it into an electronic signal. It suits GM gearboxes such as the Powerglide, TH350 and TH400.
- ESA-01 + ESA-02 adapter: for the Holden Trimatic and the M20/M21 four-speeds.
Running a 4L60E or another electronic gearbox? It already has a speed sensor output, so you don't need a converter. For the full rundown see GPS speed sensor vs ESA-01 and our TH350 electric speedometer conversion guide.
Three ways to do the conversion
| Original GTS instruments | DIY aftermarket gauges | RetroTech GTS dash kit | |
|---|---|---|---|
| Finding parts | Increasingly hard to find in good condition, and often need restoring | Gauges are easy to buy; mounts, lights and wiring you work out yourself | One kit, built to fit the GTS fascia |
| Indicator & high beam lights | Built into the gauges | Usually means drilling the fascia or limiting your gauge choice | Pilot light cluster in the clock hole, no cutting |
| Warning lights | Factory setup | Source your own sockets and globes | LED brake fail and charge lights included, charge circuit works properly |
| Speedo | Mechanical cable | Up to you | Electronic, with VSS, GPS or ESA converter options |
| Wiring | Factory GTS loom needed | Work it out yourself | Deutsch plugs plus a printed Kingswood-to-GTS wiring manual |
| Best for | Concours, factory-correct restorations | Builders who enjoy fabrication and wiring | A classic look with modern, accurate gauges and a clean install |
The RetroTech HJ–WB GTS dash kits
We designed our kits to fill every gap a reproduction fascia leaves, so you can do the whole conversion without hunting down original GTS instruments.
Complete HJ–WB GTS Dash Kit (SAAS Muscle Series 3):
- SAAS Muscle Series 3 gauges pre-installed: 80mm speedo and tacho, plus 52mm fuel, oil pressure, water temp and volts, with senders included
- 3D-printed gauge pods in high-temperature engineering-grade filament
- Pilot light cluster in the clock hole, pre-wired with LED indicators, high beam and hand brake lights
- LED brake fail and battery charge warning lights, with a resistor so the alternator charge circuit works properly
- Deutsch DT plugs, so the cluster is easy to remove and service
- A full printed manual, including Kingswood-to-GTS wiring
- Options for pre-crimped Deutsch tails, a SAAS GPS speed sensor, or ESA converters for speedo-cable gearboxes
GTS Bare Dash Kit: the same 3D-printed pods, pilot light housing and warning light sockets, for builders who want to supply and wire their own gauges. An optional pilot light set adds the LED pilot lights, T5 globes and charge-light resistor.
Already have gauges and only need the lights? The GTS pilot light cluster is sold on its own too.
Please note: the GTS dash fascia itself isn't included in any of our kits. They fit your original or reproduction fascia.
What the install involves
- Remove the old cluster and fascia.
- Do the clearance work. A few millimetres come off the two lower mounting posts on the cluster's aluminium mount. A die grinder or Dremel makes it quick.
- Wire it up: ignition, constant 12V, ground, instrument lights, fuel, tacho and speedo signals, oil and temp senders, and the pilot lights. On a Kingswood dash the factory pilot light plug is a 10-way connector, so the loom needs rewiring to suit. The manual covers this.
- Test before you assemble. Plug everything in with the fascia off and check the battery light, both indicators, high beam, hand brake and brake fail lights, then the gauges.
- Fit the fascia and calibrate the speedo (not needed with GPS).
You'll need to be confident removing the instrument cluster and doing automotive wiring. If you're not, an auto electrician can fit it. Our aftermarket gauge wiring guide covers the basics of power, earths and senders.
See it working
Common questions
Will the HJ–WB GTS dash fit my HQ?
No. The HQ uses a different dash, so these parts won't fit.
Do I have to cut my GTS fascia?
No. The indicator, high beam and hand brake lights go in the clock hole, and the warning lights use the fascia's existing windows.
Will I still have working indicator lights for roadworthy?
Yes. That's exactly what the pilot light cluster is for. It brings back the left and right indicators and the high beam light that the original GTS gauges had built in.
Does it work with an LS swap?
Yes. The SAAS gauges take electronic signals, so they suit stock engines, modified engines and LS or other modern swaps. See our LS swap gauges and senders guide.
Manual or auto?
Either. If your gearbox has a speed sensor output, connect it directly. If it still has a speedo cable, add GPS or the right ESA converter.
Is the fascia included?
No. The kits fit your original or reproduction GTS fascia.
Need a hand?
Not sure which kit or speedo option suits your car? Get in touch with your model and gearbox and we'll point you in the right direction. More parts for your car: HJ–WB Holden parts and HQ–WB side vents.